Unit sound, listed parts still available
Repair instead of replacing
We price the repair first.
Fireplace Replacement in Spring Hill, FL
A new fireplace in place of the worn-out one, with the chimney or vent its listing calls for, not the old pipe reused by habit.
Request a Free Inspection
Request Received
Thanks, your request is with us. Expect a call from our Spring Hill family to book the free inspection.
Quicker by phone? Call (352) 663-0381
10% Off Work Booked in the 72 Hours After Your Inspection
Book your fireplace replacement within 72 hours of your free inspection and take 10% off.
What You Can Count On
Fireplace replacement takes out a worn factory-built wood or gas fireplace and fits a new one in its place. Because a factory-built fireplace and its chimney are listed as one system, the new unit gets the chimney or vent named in its own listing, and the framing, hearth and face are rebuilt to the new unit's clearances.
When to Replace an Old Fireplace
A factory-built fireplace is a metal box with a matched metal chimney. It is repaired as long as its maker's parts exist and the box itself is sound. It makes sense to replace a prefab fireplace when the firebox or outer casing has rusted through, when the refractory and grates are gone and no listed parts remain, when the chimney system has failed and cannot be rebuilt to its listing, or when you want a different fuel at the same spot.
If the unit can still be put right with its own parts, that is prefab fireplace repair, and we say so before quoting a new one.
Like-for-Like Replacement in an Older Spring Hill House
Close to half of Spring Hill's housing units were built before 1990, according to the Census Bureau's 2020 to 2024 American Community Survey. Where one of those houses still has the factory-built fireplace it was built with, that unit and its chimney are the same age as the house.
Replacing it like for like means a new factory-built unit of similar size in the same framed opening. That opening may not fit the new unit exactly: framing dimensions differ between makers and models, so the opening is often reframed, and sometimes the chase or ceiling openings shift too. We do not promise to keep the old opening size until we have the new unit's framing drawing in hand.
Why the Old Chimney Rarely Stays
Section R1004.1 of the Florida Building Code, Residential, says a factory-built fireplace is installed to the conditions of its listing, tested to UL 127, and section R1005.4 says the chimney of a factory-built fireplace meets UL 127 as well. In practice the fireplace and its chimney were tested together. A new fireplace from another maker, or a newer model, names its own chimney parts in its manual.
So the old pipe and cap normally come out with the old box, and the new chimney goes in from the new unit's starter collar to its listed cap. One maker's manual is blunt about the alternative: any modification of the fireplace system, chimney components included, may void its listings and approvals and could result in an unsafe installation. Reusing an old chimney happens only when the new unit's own manual lists it, which is uncommon.
Gas Fireplace Replacement
A gas fireplace replacement follows the same logic with a vent in place of a chimney. Florida's Fuel Gas code, section 604.1, says a vented gas fireplace is listed to ANSI Z21.50 and installed to its maker's instructions, and those instructions name the vent pipe and termination. A new gas fireplace replacement unit usually brings its own direct-vent pipe and wall or roof termination, and the old vent is removed.
The gas is shut at the old unit's valve and the appliance disconnected. The supply line to the new unit is connected by a plumber or gas contractor, and the new unit's controls are set up and tested with you. A zero clearance fireplace installation, the trade name for a factory-built unit that may sit close to wood framing, is what lets a gas unit go into a framed wall where a wood unit stood.
Finishing the New Fireplace
With the new unit set and its chimney or vent run, the face is closed. Section R1004.2 says the hearth extension of a factory-built fireplace follows that fireplace's listing and is set apart from the surrounding floor, so the old hearth may need to grow or change. A masonry hearth is sized by section R1001.10: at least 16 inches in front of the opening and 8 inches past each side, more for large openings. The surround, mantel and paint follow; a new look for the face is fireplace remodel work.
The free inspection reads the old label, checks the framing, attic and chase, and talks through wood or gas. The written estimate names the new unit's listed chimney or vent and every framing and finish step. Our local, family-run company is Proudly American, and the experienced crew that removes the old unit sets the new one.
Problems We Find and Fix
Repair Options
The old unit's condition and the fuel you want decide the job.
Parts and Materials
Request Your Free Spring Hill Inspection
Leave your details and we will call back to pick a time that suits you.
- Free inspection and a written estimate
- Same-day service available
- Family owned and run in Spring Hill
Request Received
Thanks, your request is with us. Expect a call from our Spring Hill family to book the free inspection.
What Affects the Price
Signs It Is Time
When a factory-built fireplace has rusted, cracked or lost its parts, the fix is a new unit in the same spot. Our local, family-owned crew opens the face, takes out the old box and pipe, sets the new fireplace to its listed clearances, and runs the chimney or vent that was tested with it. A free inspection starts it.
Related Services
Proudly American
Run by a Spring Hill family: experienced hands, a written estimate before work starts and a workmanship warranty on our repairs.
Equipment Brands We Install and Service
Replace Your Worn-Out Fireplace
The new unit goes in with the chimney it was tested with, fitted by our Proudly American family crew.